| 规格: | Detail: Simcom300 / Simcom340 Fleet GPRS GPS GSM Personal Tracker with 159dBm Sensitivity
1 Summary
Working Based on existing GSM/ GPRS network and GPS satellites, this product can locate and monitor any remote targets by SMS or GPRS.
2 Applications
l Rental vehicle / Fleet management etc
l Protect the child / the old / the disabled / pet etc
l Protect businessmen
l Personnel management
l Covert Tracking
3 Hardware Descriptions
3.1 Front Face 3.2 Rear Face
- - - -
Content | Specs. |
Dim. | 64mmx 46mmx 17mm( 1.8* 2.5* 0.65) |
Weight | 50g |
Network | GSM/ GPRS |
Band | 850/ 1800/ 1900Mhz or 900/ 1800/ 1900Mhz |
GPS chip | SIRF3 chip |
GSM/ GPRS module | Simcom300/ Simcom340 |
GPS sensitivity | -159dBm |
GPS accuracy | 5m |
Time To First Fix | Cold status 45s Warm status 35s Hot status 1s |
Car charger | 1224V input 5V output |
Wall charger | 110220V input 5V output |
Battery | Chargeable changeable 3.7V800mAh Li-ion battery |
Standby | 48hours |
Storage Temp. | -40Cto + 85C |
Operation Temp. | -20Cto + 55C |
Humidity | 5% --95% non-condensing |
- - - -
- - - -
- - - -
5 Usage
5.1 SIM card installation
Make sure that there is no call transfer and call display is on, and PIN code off. The SMS message must in Text format, cant be identified for PDU format.
Steps:
1 Open the rear cover, and pick out the battery.
2 Push the foil along and turn it left.
5.2 Battery and Charger
Do charge the battery to capacity in 8 -12 hours for first use. Please use the battery and charger provided by the manufacturer. This unit adopts built-in Li-ion battery, and full battery will support around 48 hours use on end. After first use, the battery can be charged fully in 3-5hours.
Cautions:
a: For its Li-ion battery, which contains harmful chemicals and may burst, please dont bump, puncture it violently and keep it off fire.
b: Please charge the battery in time to keep it working normally.
5.3 Startup
l Put the SIM card and battery in place.
l Turn on the unit outdoors by pressing the on/ off button until the indicator is on.
l For first use, please initialize the unit and restore it to default setting.( please refer to 5.4 for instruction.)
l In 10 or 40seconds, the unit will begin to work and acquire the GSM signals as well as the GPS signals. The indicator will keep flashing every 4 seconds when the unit has received the signals, otherwise it will keep on.
l When this unit receives GPS signals normally, you can use it and do all the following settings.
5.4 Initialization
Send begin+ password in SMS to the unit, it will reply begin ok and initialize all the settings. ( default password: 123456)
5.5 Change the Password
Send SMS password+ old password+ space+ new password to change the password.
Remark:
5.5.1Be sure keep the new password in mind, you have to upload the software to restore the original setting in case of losing the new password.
5.5.2Make sure the new password is in 6 digits, or else the tracker can not recognize the password.
5.6 Authorization
There are only 5 numbers able to be authorized.
5.6.1 Call the tracker for 10 times, it will make the cell phone number as the authorized number automatically.
5.6.2 Send SMS admin+ password+ space+ cell phone number to set up a authorized number. The other authorized numbers should be set by the first authorized number. If the number is successfully authorized, the unit will reply admin ok! in SMS.
5.6.3 Send SMS noadmin+ password+ space+ authorized number to delete the authorized number.
5.6.4 For roaming purpose, you have to add your country code ahead of the cell phone number, for example, please send admin123456 008613322221111 to tracker to set 13322221111 as an authorized number.
5.6.5 When an authorized number dials up the unit, it will hang up and report a real-time Geo-info as below:
Lat: 22.566901 long: 114.051258 speed: 0.00 14/ 08/ 09 06.54 F: 3.85V, 1, Signal: F help me imei: 354776031555474 05 43.5 460 01 2533 720B
Lat: 22.566901 long: 114.051258= = Coordinate
0.00 = = speed
14/ 08/ 0906.54= = Date& Time
F: 3.85V = = battery power
1= charging 0 means no charging
Signal: F = Full GPS signal 0meansweak GPS signal
help me = = the SOS message, this section is blank for tracking message
354776031555474= = IMEI
05= Means you get 5 GPS fix ( from 3 to 10 )
43.5= Altitude
460= MCC Mobile Country Code
01= MNC Mobile Network Code
2533= LAC Location areacode
720B= Cell ID
( Remarl: GSM ID can be add or delect accroding to customers requirement)
5.7 Real-time Polling
5.7.1If there is no authorized number, when any number dials up the unit, it will report a Geo-info; If there is already an authorized number, then it will not respond when an unauthorized number calls it up.
5.7.2When an authorized number dials up the unit, it will hang up and report a real-time Geo-info as below:
5.8 Auto-Track
Report a Geo-info at 30s intervals to the authorized numbers for 5 times:
5.8.1 Set up: Send SMS t030s005n+ password to the unit, it will report the Geo-info at 30s intervals for 5 times.( s: second, m: minute, h: hour) . The setting must be in 3 digits and at maximum 255 in value.
5.8.2 Send SMS t030s* * * n+ password to the unit, it will reply SMS heaps of times
5.8.3 Cancel: Send notn+ password to delete the auto track
Remark: the interval must not be less than 5s.
5.9 MonitoringMode( Voice Surveillance)
SendSMS monitor+ password, the response from the tracker is monitor ok In this mode, the user can dial up the unit to hearthe voice around the tracker after your call.( please refer to 5.10 for instruction) .
5.10 Modes switch between track and monitor
5.10.1.The default mode is track.
5.10.2. Send SMS monitor+ password to the unit, and it will reply monitor ok! and switch to monitormode.
5.10.3. Send SMS tracker+ password to the unit, it will reply tracker ok! and restore to track mode.
5.11 Geo-fence
Set up a geo-fence for the unit to restrict its movement within a district. The unit will send message to the authorized numbers when it moves out of the district.
Notes: This function will be invalid if the unit moves outside the district. You need to re-set it if you want this function again.
5.11.1Send SMS stockade+ password+ space+ latitude, longitude; latitude, longitude to the unit to set the restricted district.
Remark: The first latitude& longitude is coordinate of the top left corner of the Geo-fence, while the second latitude& longitude is the coordinate of the bottom right corner. It will alarm one time in each setting.
5.11.2Cancel: Send SMS nostockade+ password to deactivate this function.
5.11.3Response SMS format: stockade! + geo-info to the authorized numbers. It will alarm one time in each setting.
5.12 Movement Alert
This function is using for the owner to get alarm when the trackermovesoutofarestricteddistrict.
5.12.1Set up: SendSMS move+ password to the unit to set the movement alert.then the unit will reply move ok! . In case of such a movement, it will send SMS Move along with a Geo-info to the authorized numbers. It will alarm one time in each setting.
5.12.2Cancel: Send SMS nomove+ password to deactivate the movement alert.
Remark: This function will be out of effect after the unit moves outside the district.
ResponseSMS format: move! + geo-info. Itwill alarm one time in each setting.
5.13 Overspeed Alert:
This function is using for the owner to control the targets speed.
5.13.1Set up: Send SMS speed+ password+ space+ 080 to the unit ( suppose the speed is 80km/ h) , and it will reply speed ok! . When the target moves exceeding 80 km/ h, the unit will send SMS speed+ 080! + Geo-info to the authorized numbers. Itwill keep sending such an alert every 3minutes.
5.13.2Cancel: Send SMS nospeed+ password to deactivate the overspeed alert
Remark: It is recommended that the speed alarm is set at not less than 50km/ h. For below that rate, it may cause the excursion of the GPS signal influenced by clounds etc.
Response SMS format: speed+ 080! + Geo-info ( suppose the speed is 80km/ h) .
The tracker will check the speed in 10 minutes interval and alarm if it is overspeed.
5.14 IMEI Checking:
Send SMS imei+ password to the unit to check the IMEI number of the tracker.
5.15 SOS Button
Press the SOS for 3 second, it will send help me ! + Geo-info to all the authorized numbers every 3 minutes. It will stop sending such a SMS when any authorized number reply SMS help me! to the tracker.
5.16 Low Battery Alert
It begins to send SMS to the user every 30minutes when the the battery voltage is 3.7V.
SMS format: low battery+ Geo-info.
5.17 Hidden Number Tracking
When a hidden authorized number calls the tracker, the tracker will reply SMS with the hidden number& Geo-info to all the authorized numbers.
5.17.1Send SMS hide number to set up the hidden number.
5.17.2 Send SMS nohide number to delete the hidden number.
5.18 SMS Center
5.18.1Send SMS adminsms+ password+ space+ cell phone number to set the SMS center.
If the SMS center is set up, when an authorized number sends SMS to the tracker, the tracker will reply a SMS with Geo-info & authorized number to SMS center.
5.18.2Send SMS noadminsms+ password to cancel the SMS center.
Response SMS format: authorized number+ Geo-info
5.19 GSMID( this function can be add or delect forcustomization.)
There is GSM ID in each SMS from the tracker. The location of the tracker can be found according to the GSM ID in case of no GPS signal. GSM ID is make up of MCC( Mobile Country Code) , MNC( Mobile Network Code) , LAC( Location areacode) and Cell ID.( refer to 5.6.5)
5.20 Motion Sensor( this function can be add or delect forcustomization.)
This function is using for the user to get alarm info when someone touchs the unit.
5.20.1 Setup: Sendshake+ password+ space+ 1-10 to the tracker to set up this function.( 1-10 means the level of intensity)
5.20.2 Send SMS shake+ password+ space+ 1is the lightest level of intensity.thetracker will sendalert if someone touchs the unit heavily.
5.20.3 Send SMS shake+ password+ space+ 10 is the strongest level of intensity.thetracker will sendalert if someone touchs the unit slightly.
5.20.4 Cancel: Send SMS shake+ password+ space+ 0to remove this function.
5.21SD card function
A mini SD card can be put in the trackers SD card slot. The GPRS data can be saved in the SD card if GPRS is off. It will senddata to the GPRS server again if GPRS is on.
5.21.1 Setup: Send SMS sdlog123456 1 to the tracker to activate the function of storing data in SD card;
Cancel: Send SMS sdlog+ password+ 0 to the tracker to deactivate the function of storing data in SD card.
5.21.2 Setup: SendSMSreadsd+ password+ space+ 1to ask the tracker to send data in the SD card to the GPRS server.
Cancel: Send SMS readsd+ password+ space+ 0to ask the tracker to stop sending data in the SD card to theserver.
5.22 GPRS Setting
In order to use GPRS function, the user needs to set IP, Port and APN ( access point name ) by either cell phone, or our PC software.
( NOTE: Some countries or regions should set APNs User Name and APNs Password.)
5.22.1 Set an IP address and port:
Setup: Send SMS adminip+ 123456+ space+ IP address+ space+ port.
If setup successful, the tracker will reply SMS adminip ok
Cancel: Send SMS noadminip+ 123456
5.22.2 Set APN
Setup: Send SMS apn+ 123456+ space+ specify apn content.
If setup successful, the tracker will reply SMS APN ok.
Cancel: The old APN will be invalid automatically when a new APN is set.
5.22.3 Set APNs User Name
Setup: Send SMS apnuser+ 123456+ space+ the sim cards user name.
If setup successful, the tracker will reply SMS apnuser ok.
Cancel: The old APN user name will be invalid automatically when a new APN uer name is set.
5.22.4 Set APNs Password
Setup: Send SMS apnpassword+ 123456+ space+ the sim cards password.
If setup successful, the tracker will reply SMS apnpasswrod ok.
Cancel: The old APN password will be invalid automatically when a new APN password is set.
5.22.5 GPRS transport protocols
As soon as the IP & Port & APN are set up, the user can make a call or send SMS to tracker. The tracker will hand up and report the coordinates to IP address.
The message format sent by tracker to IP address is as following:
Serial number + authorized number + GPRMC + GPS signal indicator + command + IMEI number + CRC16 checksum.
For example:
090907070718, 13145826175, GPRMC, 070718.000, A, 2234.0228, N, 11403.0764, E, 0.00, , 070909, , , A* 73, F, , imei: 354776030042714, 05, 50.1, F: 4.11V, 0, 132, 40512, 460, 01, 2533, 720B
090907070718= = serial number( date& time)
13145826175= = = authorized number
GPRMC, 070718.000, A, 2234.0228, N, 11403.0764, E, 0.00, , 070909, , , A* 73, = = GPSmodes OriginalGPRMC sentences
F= = = FullGPS signal L= = = NoGPS signal
imei: 354776030042714= = the trackers IMEI number
05= = = get 5 GPS number
50.1= = = Altitude
F: 4.11V= = = Full batterypower L: 3.65V= = = Lowbatterypower
0= = = No charging 1= = = charging
132= = = The length of the GPRS string
40512= = = CRC16Checksum
460= = = 460= MCC Mobile Country Code
01= = MNC Mobile Network Code
2533= = 2533= LAC Location areacode
720C= = 720B= Cell ID
( NOTE: GSM ID can be add or delect accroding to customer; s requirement.)
For example, it will send GPS coordinates as below illustrated
Notes:
Our gprs supports TCP or UDP protocol, so please confirm whether your GPRSWebserver supports TCP or UDP protocol before having the order.
please use the SIM card which is with GPRS function.
Plsuse the following SMS to set up GMT time in the SMS for the tracker time zone+ password+ space+ the customers GMT TIME
Plsuse the following SMS to set up YOURwebsite in the SMS for the tracker home+ password+ space+ the customers WEBSITE
home+ password+ space+ space ( ifthere is no website in the SMS)
6 Cautions
Please comply with the instructions to extend the unit life:
1. Keep the unit dry. Any liquid, i.e. rain, moisture, may destroy or damage the inside circuitry.
2. Dont use & store the unit in dusty places.
3. Dont put the unit in overheated or overcooled places.
4. Handle carefully. Dont vibrate or shake it violently.
5. Clear the unit with a piece of dry cloth. Dont clean in chemicals, detergent.
6. Dont paint the unit, this may cause some foreign materials left in between the parts.
7. Dont disassemble or refit the unit.
8. Please use the battery and charger provided by manufacturer. Using other batteries and chargers will cause unwanted situation.
9. Dont dismount the antenna randomly, or use other antennas. This may interfere with the transmission, and increase the radiation as well.
7 Faults & The solutions
- - - -
Faults | Solution |
Startup Fail | Check the battery and see if it is fully charged or correctly installed. |
Hang up Fail | In existence of an authorized number, an unauthorized number dials up the unit. Please initialize the unit and re-set up the authorized numbers. |
Monitor Fail | Check if the authorized number is setup or in the coverage of signals. |
Location report in digits of zeros | Dont use it in the place beyond reach of signals. Place the unit outdoors, especially when starting it up. |
- - - -
Model Number: TK101
Brand Name: Dragon
Payment Terms: Pay in adva
Minimum:
Certification: CE, FCC, IP65
Delivery Time: 5 working days
Supply Ablity: |
|---|
